ELCOMETER 345 PDF
The Elcometer range of digital coating thickness gauges has been specifically designed to provide highly accurate, reliable and repeatable coating thickness. The Elcometer Coating Thickness. Gauge is an incredibly versatile gauge. With a range of probes in both Integral or Separate probe versions for coating. Elcometer Coating Thickness Gauge. Operating Instructions. English. R. English Equipment described in these instructions is covered by the following.
|Published (Last):||6 October 2013|
|PDF File Size:||1.96 Mb|
|ePub File Size:||15.4 Mb|
|Price:||Free* [*Free Regsitration Required]|
With the gauge switched on, press. There are 1 items available.
Lift the probe from the surface. Published on Apr View In the unlikely event of a fault, the gauge should be returned to your local Elcometer supplier or directly to Elcometer. Marshall Manual – Manual An intermediate foil thickness can also be used to confirm the performance over the calibrated range.
Press to elcoketer the error message. Immediate payment required for this item. Postage cost can’t be calculated.
To fit or replace batteries: The eddy current principle is used for non-conductive coatings on non-ferrous metals substrates. If you do stumble upon a link that isnt functioning, do tell us ecometer that and we will try to answer you as fast as Elcometer User Manual for Mac lets you make basic image edits like cropping If is pressed the gauge displays the previous statistical value on the user list for a minimum of 3 seconds.
The feature is elcometfr off by selecting OFF. Elcometer User Manual for Mac Switch the gauge on and pressthe symbol in the display will flash.
Alternatively visit the Elcometer website, www.
Elcometer Coating Thickness Gauge
elcomter If required, this reading can be adjusted for the conditions of the measurement – see Calibration adjustment on page This is either due to a very high electrical noise environment, beyond emc specification limits, or could indicate a gauge fault.
Do not hesitate to contact Elcometer or your Elcometer supplier if you have any questions.
Switch off the gauge. Elcometer Inc, Michigan Office Relocation. After 4 seconds C appears in the left-hand side of the display and the value will start to change. If the following display appearsFRIntegral probe0RSeparate probethe value is just greater than the range of the gauge, or the gauge is out of calibration. Back to home page.
Your Elcometer can be used for this. The bleeper will sound to indicate acceptance of the new calibration.
[BELLA]Elcometer 345 Coating Thickness Gauge
Elcometer are world leaders in the design, manufacture and supply of inspection equipment for coatings and concrete. If required the calibration adjustment can be repeated to ensure its accuracy.
Delivery times may vary, especially during peak periods. A copy of this Instruction Manual is available for download on our Website via www. What the box contains. All other trademarks acknowledged. Elcometer User Manual for Mac comes with powerful features such as editing Documents. If the probe is left on the bare substrate or moved quickly to the calibration foil the display will show a sequence of three rising – symbols and sound a series of bleeps as a warning.
Switch on and try again. To switch off, press and hold The gauge will switch off automatically after one minute of inactivity. Statistics data must be cleared see Section 6. When the batteries are exhausted, the gauge will beep three times and then switch off.
Elcometer gauges have a backlit display. It is best to use an uncoated item that is similar to the coated item to be tested. Comes with wired probe, and calibration shims not pictured. Monroe, North Carolina, United States. Mouse over to zoom – Click to enlarge.
Elcometer Coating Thickness Gauge Probe Range A range of fully interchangeable probes for the Elcometer separate coating thickness gauge. The principle of electromagnetic induction is used for non-magnetic coatings on magnetic substrates such as steel.
Elcometer Digital Coating Thickness Gauge | eBay
Regular calibration checks are a requirement of quality management procedures e. Statistics overflow, more than 9, readings have been taken. To exit from elcometter setting menu and retain the current user list press.
When eldometer value in the display is correct, press to accept the new calibration or wait 7 seconds for the gauge to accept the calibration automatically. To re-calibrate, repeat the procedure. Calibration factors are out of range. Elcometer IPC Dry Film Thickness Gauge Pre-calibrated with 4 surface profiles, is designed to measure dry film thickness on shot or grit blasted substrates.